MANUFACTURED BY: McCULLOCH MOTORS CORP. LOS ANGELES, CALIFORNIA, U.S.A.SERIES OR ASSEMBLY NUMBER: 600016YEAR INTRODUCED: 1977YEAR DISCONTINUED: 1983ENGINE DISPLACEMENT: early models 2.1 cu. in. (34.4 cc)late models 2.0 cu. in. (32.8 cc)NUMBER OF CYLINDERS: 1CYLINDER BORE: 1.430 in. (36.5 mm) for 2.0 cu. in.PISTON STROKE: 1.201 in. (30.5 mm) for 2.0 cu. in.CYLINDER TYPE: Aluminum with chrome plated boreINTAKE METHOD: Piston portedMANUFACTURER ADVERTISED H.P.: WEIGHT : 10.1 lbs. (4.6 kg) powerhead onlyOPERATOR CONFIGURATION: One Man operationHANDLEBAR SYSTEM: CHAIN BRAKE: CLUTCH: CentrifugalDRIVE TYPE: DirectCONSTRUCTION: Injection molded plastic & die cast magnesiumMAGNETO TYPE: Solid stateCARBURETOR: Walbro MDC 16 or Zama M1-M7MAJOR REPAIR KIT: MINOR REPAIR KIT: AIR FILTER SYSTEM: Flocked wire screenSTARTER TYPE: Automatic rewindOIL PUMP: Automatic with manual overrideOPERATING RPM: IGNITION TIMING: 26 degrees before TDCBREAKER POINT SETTING: noneFLYWHEEL/COIL AIR GAP: SPARK PLUG TYPE: AC CS45TSPARK PLUG GAP: 0.025 in. (0.63 mm)CRANKSHAFT MAIN BEARINGS: Caged needle rollerFUEL TANK CAPACITY: 10.8 oz. (320 ml)FUEL OIL RATIO: 40:1 with McCulloch oilRECOMMENDED FUEL OCTANE: RegularMIX OIL SPECIFICATION: McCulloch two-cycle mix oilCHAIN PITCH: 3/8 in. low profileCHAIN TYPE: McCullochBAR MOUNT PATTERN: SHORTEST GUIDE BAR SUPPLIED: 12 in. (30 cm)LONGEST GUIDE BAR SUPPLIED: 16 in. (40 cm)COLOUR SCHEME: McCulloch Yellow with Black handles, starter and air filter covers
- Mcculloch Mac 130 Chainsaw Service Manual 2016
- Mcculloch Mac 130 Chainsaw Service Manual Review
- Mcculloch Mac 130 Chainsaw Service Manual Pro 222
- Mcculloch Mac 130 Chainsaw Service Manual Instructions
McCulloch Chainsaw Manuals McCulloch MCC1514 Electric Chainsaw Owners Manual. McCulloch Mac 3-16XT Chainsaw Service Parts List. Posted in Chainsaw Manuals, Mac Chainsaw Manuals, McCulloch Chainsaw Manuals More. McCulloch Mac 3-14XT Chainsaw Service Parts List. Posted in Chainsaw Manuals, Mac Chainsaw Manuals, McCulloch Chainsaw Manuals. Mcculloch manuals are a must for the DIY person, offering part numbers, service and repair information, as well as original owners / operators instructions and specifications. Buy it today and get Free Shipping! The McCulloch Power Mac 310 chain saw is a somewhat vintage model. It was new about the same time the first personal computers came on the market, in the mid 1980s. Like most chain saws, it has.
Related Articles
- 1 Adjust a Poulan Chain Saw Bar Chain Oil Flow
- 2 Stihl Chain Oiler Trouble
- 3 Fix Chain Oil Problems on a Stihl Chain Saw MS290
- 4 Tell if a Chain Saw Oiler Goes Out
McCulloch chain saws, like all other chain saws, require continuous lubrication during use to prevent the chain from catching on the wood being cut. Without the proper lubrication, kickback or pull-in of the chain saw blade may occur, putting you at risk for catastrophic injury. McCulloch chain saws are equipped with automatic oilers and lack the chain oil adjustment screw that many other brands possess. In spite of that fact, you can still take measures to adjust the amount of oil that coats the chain saw chain during use.
1
Fill the chain saw chain oil reservoir with the type of oil recommended by McCulloch. Refer to the operator's manual to ascertain which oil is recommended for your model. Avoid adding an excess amount of oil to the container. Drain some of the oil if the tank is already overfilled which you check it. Too little or too much oil in the reservoir can alter the machine's output. Mongodb manual install mac.
2
Assess the oil output of the chain saw bar oiler to determine whether or not adjustment is necessary. Allow the chain saw to run for 2 to 3 minutes to warm up. Point the tip of the chain saw toward a light-colored surface and hold it about 6 inches away. Increase the throttle, allowing the chain to rotate several times. Stop the chain saw and check the surface for the telltale splatter of oil that proves the lubrication is being applied to the blade.
3
Loosen the chain saw guide bar and remove the chain from it. Wrap the end of a toothpick in a soft cloth and use it to clean out the channel that runs the length of the blade. Cleaning the channel ensures that the space is free for chain oil to flow through and properly lubricate the chain.
4
Unclog the hole that emits the oil from the automatic oiler to allow the oil to flow freely. Insert the tip of a paper clip that's been straightened into the hole, and work it in and out to ensure the passage is free.
Things You Will Need
- Chain saw chain oil
- Light-colored surface
- Toothpick
- Soft cloth
- Paper clip
Tip
- Check the bar lubrication before each use of the chain saw.
Warning
- Never use waste oil in a chain saw chain oil reservoir.
References (2)
Mcculloch Mac 130 Chainsaw Service Manual 2016
About the Author
Mcculloch Mac 130 Chainsaw Service Manual Review
Amie Taylor has been a writer since 2000. Book reviews, gardening and outdoor lawn equipment repair articles and short fiction account for a handful of her published works. Taylor gained her gardening and outdoor equipment repair experience from working in the landscaping and lawn-care business she and her husband own and operate.
Photo Credits
- Comstock Images/Stockbyte/Getty Images
Choose Citation Style
Mcculloch Mac 130 Chainsaw Service Manual Pro 222
Taylor, Amie. 'How to Adjust the Oiler on a McCulloch Chainsaw.' Home Guides | SF Gate, http://homeguides.sfgate.com/adjust-oiler-mcculloch-chainsaw-101872.html. Accessed 25 August 2019.
Taylor, Amie. (n.d.). How to Adjust the Oiler on a McCulloch Chainsaw. Home Guides | SF Gate. Retrieved from http://homeguides.sfgate.com/adjust-oiler-mcculloch-chainsaw-101872.html
Taylor, Amie. 'How to Adjust the Oiler on a McCulloch Chainsaw' accessed August 25, 2019. http://homeguides.sfgate.com/adjust-oiler-mcculloch-chainsaw-101872.html
Mcculloch Mac 130 Chainsaw Service Manual Instructions
Note: Depending on which text editor you're pasting into, you might have to add the italics to the site name.